The ASTM A192 belongs to the carbon seamless tubes, which is specially designed for high, middle, low pressure purpose in seamless carbon steel boilers and as super heater tubes.
ASTM A192 specification has been approved for use by agencies of the Department of Defense. Consult the DoD Index of Specifications and Standards for specific year of issue which has been adopted by the Department of Defense.
Size (mm): O.D.:6.0-114.0 W.T.:1-15 L:max 12000
Delivery Condition : As different requirements,It including pickling,etc.
Delivery Condition : As different requirements,It including pickling,etc.
Test:
1.Hydrostatic or Nondestructive Electric Test
2.Heat Treatment:Min temperature 650.
3.Surface Condition:Free of scale,A slight amount of oxidation will not be considered as scale.
4.Flattening Test,Flaring Test.Flange Test,Hardness Test,Hydrostatic Test
1.Hydrostatic or Nondestructive Electric Test
2.Heat Treatment:Min temperature 650.
3.Surface Condition:Free of scale,A slight amount of oxidation will not be considered as scale.
4.Flattening Test,Flaring Test.Flange Test,Hardness Test,Hydrostatic Test
Inspection and Test:
Chemical Composition Inspection, Mechanical Properties Test(Tensile Strength,Yield Strength, Elongation, Flaring, Flattening, Bending, Hardness, Impact Test), Surface and Dimension Test,No-destructive Test, Hydrostatic Test.
Chemical Composition Inspection, Mechanical Properties Test(Tensile Strength,Yield Strength, Elongation, Flaring, Flattening, Bending, Hardness, Impact Test), Surface and Dimension Test,No-destructive Test, Hydrostatic Test.
Surface treatment:
Oil-dip, Varnish, Passivation, Phosphating, Shot Blasting.
Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles.
Oil-dip, Varnish, Passivation, Phosphating, Shot Blasting.
Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles.
Chemical Compositions(%) of ASTM A192
| C | Si | Mn | P | S | Cr | Mo | Cu | Ni | V |
| 0.06-0.18 | ≤0.25 | 0.27-0.63 | ≤0.035 | ≤0.035 | / | / | / | / | / |
Mechanical Properties of ASTM A192
| Yield Strength (Mpa) | Tensile Strength (Mpa) | Elongation (%) |
| ≥180 | ≥325 | ≥35 |
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Scope
- This specification covers minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service.
- The tubing sizes and thicknesses usually furnished to this specification are ½ in. to 7 in. [12.7 to 177.8 mm] outside diameter and 0.085 to 1.000 in. [2.2 to 25.4 mm], inclusive, in minimum wall thickness. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification.
- Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or 0.015 in. [0.4 mm] thickness.
- The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
Note:
- Mill test certificates will be issued according to EN10204.3
- All tubes shall be supplied as per applicable ASTM Specification.
- The tubes Shall be Seamless and the testing shall be as per A 450 / A450M.
Application: apply to the heat exchangers, condensers and heat transfer equipment and similar pipe.
Marking:
- Pipes are supplied with marking according to standard and customer request.
- Marking is paint on the ends of pipes.
- The same data, as well as additional information per customer’s request, is indicated on the bundle’s tags.
Delivery:
- Pipes are supplied in hexagonal bundles or round bundles tied with steel strip.
- Weight of bundle – up to 5000 kg upon request of customer.
- Each bundle is furnished with three tags.
